Bandit Industries is very proud to be a leading manufacturer when it comes to safety in the wood and waste processing industries, whether it be through educational seminars conducted at authorized Bandit dealerships, or through the continual research and development of equipment and features. Bandit consistently exceeds ANSI and OSHA safety requirements and recommended practices.
Regardless of the time and effort invested by manufacturers to minimize risks, accidents can still happen. In nearly all cases, such accidents are due to operator error. These errors are most common among established professionals who’ve become accustomed to equipment and take safety precautions for granted. Your safety, and the safety of those working with you, depends on your knowledge of how to properly operate and maintain your equipment. Never take the equipment or safety procedures for granted.
This section provides overviews for the safe operation of Bandit equipment, and special features on Bandit equipment that help promote safety. It is not a substitute for reading and understanding all equipment manuals, safety decals on equipment, and safety videos.
Do you need a start-up/operations and safety video for your Bandit equipment? Contact Bandit Industries at 800-952-0178 to request a complimentary DVD.
This general overview applies to all Bandit Equipment. For specific procedures, always consult your equipment operator’s manual and start-up/operations and safety video.
Personnel and bystander safety must always be the number one concern. Always wear all required personal protective equipment, per OSHA and your company’s requirement. Do not wear ragged, torn or loose clothing, large cuffed ‘gauntlet style’ gloves, jewelry or anything that could be easily snagged.
Always make sure that all controls, shields, guards and safety devices are securely in place, in proper working condition and function smoothly prior to operation.
Never operate or work on Bandit equipment while under the influence of alcohol or drugs. Always keep a fully charged, operational fire extinguisher nearby.
Never allow anyone near Bandit equipment while it is running. Any unauthorized personnel must be kept well away from the work zone at all times. Shut the machine down immediately if unauthorized persons or animals enter the work zone. Only adults should operate this equipment.
The area around Bandit equipment must be free of any objects that could obstruct the operator’s movement. Remove branches, limbs, rocks, etc. from the work area that may cause a tripping hazard for operators or workers. The operator must be located within easy reach of all controls and shut-off devices, and be prepared to react to an emergency situation.
Never allow material to discharge toward people, animals, vehicles or structures.
Never operate Bandit equipment that is in need of repair.
Never go near hydraulic leaks. High pressure oil can easily puncture skin, causing serious injury or death. Hot fluid under pressure can cause severe burns--never use fingers or skin to check for leaks.
Always use wheel chocks to secure towable Bandit machinery. Hand-fed chippers should always be connected to a tow vehicle when in use.
Never sit, stand, lay, climb or ride anywhere on Bandit equipment while it is running, operating or in transit.
Under no circumstances should anyone attempt to open, leave open or close the hoods, doors or guards on equipment while components are turning, coasting to a stop or the engine is running. This negligent action can cause severe injury or death.
This general overview highlights standard and optional equipment available on new Bandit hand-fed chippers. These features can also be retrofitted to older Bandit hand-fed chippers. For specific features applicable to your machine, always consult your equipment operator’s manual.
Pusher Paddle (STANDARD): Designed to assist operators in feeding smaller material into the chipper, the wood pusher paddle allows operators to push material from the infeed tray into the feed wheels without reaching in past the infeed hopper. It can be chipped without causing damage to the chipper. Under no circumstances should operators reach beyond the leading edge of the infeed hopper to push material to the feed wheels. If your push paddle is missing or damaged, replacements can be ordered through Bandit.
Last Chance Cables (STANDARD): Bandit’s patented last chance cables are located inside the infeed hopper. If the cables are pulled, the feed wheels will reverse direction or stop. Should a negligent operator fail to follow safety procedures and wind up in the infeed hopper being pulled towards the feed wheels, pulling these cables may be their “Last Chance” to avoid serious injury or death. The “Last Chance Cables” are NOT intended for use during normal, proper operation. Never reach into the infeed hopper to pull these cables—they are for emergency use only.
Line/Rope Shear device (STANDARD): The line/rope shearing device installs in the drum housing on Bandit drum-style hand-fed chippers and acts as a counter-knife. It’s designed to improve the chance of severing a rope, line, or similar item should it be drawn into the chipper knives. This patent-pending device is standard on all current Bandit drum-style hand-fed chippers.
Folding Infeed Tray (STANDARD): Bandit hand-fed chippers feature standard folding infeed trays to assist with transportation. Non-folding, heavy-duty welded infeed trays are optional. If equipped with the folding infeed tray, it must be locked in the open position whenever the chipper is being operated, and folded closed for transport. These devices must be in proper operational working condition at all times.
Lock Pins (STANDARD): All Bandit hand-fed chippers are equipped with a chipper hood lock pin, designed with a keyed padlock to secure the chipper hoods and doors in the closed position. Never use a homemade or make-shift hood pin system.
Engine Disable Plug (STANDARD): The housings for the chipping discs and drums are equipped with an engine-disable plug attached to the hood locking pin. This safety device helps ensure the locking pin is properly installed, or the engine will not operate.
Hood Spring Lock Pin (STANDARD): On disc-style chippers, Bandit also installs a patented safety feature called the “Hood Spring-Lock Pin”. This item is positioned so that it stops the retracting movement of the hood lock pin if the chipper disc is still turning. The hood cannot be opened while the disk is spinning.
Safety Decals (STANDARD): There are numerous decals located on the machine that contain important information to assist in operating your equipment safely. It is necessary for all machine owners, operators and service people to be familiar with, and follow all instructions as listed on the decals. It is the responsibility of equipment owners to review these decals with all employees, and keep the decals in readable condition. Replacement and multilingual decals are available through Bandit Industries.
Bottom Bump Bar (OPTIONAL): Positioned at the bottom of the infeed tray, the bump bar is designed to cut hydraulic power to the feed system when tripped. Because it operates hydraulically, the bottom bump bar is more resistant to accidental engagement from material entering the chipper normally. It offers additional means to disengage the feed system in the event of an emergency situation.